RANCANG BANGUN PROTOTYPE INTELLIGENT BOOTH KAKI LIMA (OTOMATISASI BUKA/TUTUP)

Thomas Thomas; Wawan Nurmansyah

doi:10.33557/jurnalmatrik.v21i1.522

Thomas Thomas Universitas Katolik Musi
Wawan Nurmansyah Universitas Katolik Musi

DOI: https://doi.org/10.33557/jurnalmatrik.v21i1.522

Keywords: Arduino,, intelligent,, booth, prototype

Abstract

A food and beverage booth owner who sells alongside the road, has difficulty when opening and closing the booth also when the rain comes suddenly - suddenly the owner has difficulty protecting electronic equipment from rainwater which can cause a short circuit, because the process is still done manually. To overcome this problem, a system with a microcontroller circuit using Arduino Uno and a DC motor can be made that can open and close the booth with a push button command that can facilitate the process which is still done manually and with a rain sensor circuit that can detect rain as an order to close the front of the booth to protect electronic equipment from rainwater. This system is implemented in an intelligent booth prototype to test whether the algorithm made can overcome the problems experienced by the booth owner.

References

[1] Sutojo, T., Mulyanto Edy., Suhartono Vincent. 2011. Kecerdasan Buatan. Andi, Yogyakarta.
[2] Nainggolan, Sallye Handayani. (2018). Perancangan Alat Pembuka Dan Penutup Atap Otomatis Pada Pengeringan Bij Kopi Berbasis Mikrokontroler ATmega 8. Skripsi, Fakultas Matematika Dan Ilmu Pengetahuan Alam, Universitas Sumatera Utara Medan.
[3] Harahap, Nur Apipah. (2018). “Perancangan Prototype Jemuran Otomatis Menggunakan Sensor Air Dan Sensor Ldr Berbasis Mikrokontroler Arduino Uno Dengan Metode Flc”, Media Informatika Budidarma 2(1), 15-25.
[4] Hakim, Ahmad Rofiq., Lailiyah, Siti., Suntoro, Fachrul Arlan. (2018). “Prototipe Penjemur Pakaian Otomatis Berbasis Arduino Uno”, Just Ti 1(10), 16-21.
[5] Syahminan. (2018). Prototype Pengering Biji Jagung Berbasis Mikrokontroler, SMATIKA Jurnal 1.
[6] Lestari. (2018). Rancang Bangun Atap Otomatis Dengan Menggunakan Sensor Rain Drop Dan Ldr (Light Dependent Resistor) Berbasis Atmega, Skripsi, Fakultas Matematika Dan Ilmu Pengetahuan Alam, Universitas Sumatera Utara Medan.
[7] Kadir, Riny., dan Berikang, Reonaldy. (2018). Simulasi Jemuran Otomatis Berbasis Mikrokontroler Atmega328, Seminar Nasional Teknologi.
[8] Marpaung, Nur. (2017). “Perancangan Prototype Jemuran Pintar Berbasis Arduino Uno R3 Menggunakan Sensor LDR Dan Sensor Air” Riau Journal Of Computer Science 2(3), 71-80.
[9] Feriska, Adnan., dan Triyanto, Dedi. (2017). “Rancang Bangun Penjemur Dan Pengering Pakaian Otomatis Berbasis Mikrokontrole”, Jurnal Coding Sistem Komputer Untan 2(5), 67-76.
[10] Dewi, Andriana Kusuma., Hadi, M. Sholihul., Anwar, Syaiful. (2017). “Sistem Kendali Buka Tutup Atap Rumah Untuk Smartphone dengan Menggunakna Android Smartphone” Jurnal Teknologi dan Sistem Komputer 5.
[11] Hansen, Dean., Hoendarto, Genrawan., Lina. (2016). “Perancangan Perangkat Penyiram Tanaman Otomatis Menggunakan Mikrokontroler Arduino Uno”, Jurnal InTekSis 2(4).
[12] Damastuti, Natalia., dan Syafi’i, imam. (2016). “Sistem Otomasi Atap Bangunan Pada Gudang Pengeringan Jagung Berbasis Arduino Uno”, Jurnal NARODROID 1.
[13] Siswanto, Deny., dan Winardi, Slamet. (2015). “Jemuran Pakaian Otomatis Menggunakan Sensor Hujan Dan Sensor Ldr Berbasis Arduino Uno”, Jurnal NARODROID 2.
[14] Pressman, Roger S. 2010. Software Engineering: A Practitioner’s Approach, Sevent Edition. New York: McGraw-Hill Education.
[15] Untoro, Wisnu Yudo. 2010. Algoritma dan Pemograman. Graha Ilmu, Yogyakarta.